Home
Power supplies
Power supplies for building automation
Phoenix PSU Step 3-PS/1AC/24DC/2.5/PT

Phoenix PSU Step 3-PS/1AC/24DC/2.5/PT

8 In stock

SKU

1088491

€67.16 €54.60

Details

Input data
Supply system configuration	Star network (TN, TT, IT (PE))
Input voltage range	100 V AC ... 240 V AC -15 % ... +10 %
Derating	< 100 V AC ... 85 V AC (1 %/V)
Typical national grid voltage	120 V AC
Typical national grid voltage		230 V AC
Voltage type of supply voltage	AC/DC
Inrush current	typ. 28 A (25 °C)
Inrush current integral (I²t)	typ. 0.9 A²s
Frequency range (f_N)	50 Hz ... 60 Hz ±10 %
Mains buffering time	typ. 25 ms (120 V AC)
Mains buffering time		typ. 130 ms (230 V AC)
Current consumption	1.2 A (100 V AC)
Current consumption		0.64 A (240 V AC)
Protective circuit	Transient surge protection; Varistor
Switch-on time	typ. 2 s
Device mains fuse	4 A internal (device protection), slow-blow
Recommended breaker for input protection	6 A ... 16 A (Characteristics B, C, D, K)
Discharge current to PE	< 0.25 mA
Input voltage range	110 V DC ... 250 V DC -20 % ... +40 %
Derating	< 110 V DC ... 88 V DC (1 %/V)
Current consumption	0.61 A (110 V DC)
Current consumption		0.26 A (250 V DC)

Output data
Efficiency	> 89 % (120 V AC)
Efficiency		> 90 % (230 V AC)
Efficiency Level	VI
Nominal output voltage	24 V DC
Setting range of the output voltage (U_Set)	22 V DC ... 27 V DC (> 24 V DC, constant capacity restricted)
Nominal output current (I_N)	2.5 A
Short-circuit-proof	yes
No-load proof	yes
Derating	> 50 °C ... 70 °C (2 % / K)
Crest factor	typ. 3,4
Crest factor		typ. 4.08
Output power (P_N)	60 W
Connection in parallel	yes, for increasing power and redundancy with diode
Connection in series	yes, for increased output voltage
Feedback voltage resistance	≤ 35 V DC
Protection against overvoltage at the output (OVP)	< 35 V DC
Residual ripple	typ. 100 mV_PP
Control deviation	< 0.5 % (Static load change 10 % ... 90 %)
		< 3 % (Dynamic load change 10 % ... 90 %, (10 Hz))
		< 0.1 % (change in input voltage ±10 %)
Rise time	typ. 100 ms (U_Out = 10 % ... 90 %)
Minimum no-load power dissipation	< 0.21 W (120 V AC)
Maximum no-load power dissipation	< 0.21 W (230 V AC)
Minimum nominal load power dissipation	< 6.8 W (120 V AC)
Power loss nominal load max.	< 6.2 W (230 V AC)

Connection data
Input
Position	1.x
Conductor connection
Connection method	Push-in connection
rigid	0.2 mm² ... 2.5 mm²
rigid		1 mm² (recommended)
flexible	0.2 mm² ... 2.5 mm²
flexible		1 mm² (recommended)
flexible with ferrule without plastic sleeve	0.5 mm² ... 1.5 mm²
flexible with ferrule without plastic sleeve		1 mm² (recommended)
flexible with ferrule with plastic sleeve	0.2 mm² ... 1 mm²
flexible with ferrule with plastic sleeve		1 mm² (recommended)
rigid (AWG)	24 ... 14 (Cu)
rigid (AWG)		17 (recommended)
Stripping length	10 mm (rigid/flexible)
Stripping length		10 mm (Ferrule)
Output
Position	2.x
Conductor connection
Connection method	Push-in connection
rigid	0.2 mm² ... 2.5 mm²
flexible	0.2 mm² ... 2.5 mm²
flexible with ferrule without plastic sleeve	0.5 mm² ... 1.5 mm²
flexible with ferrule without plastic sleeve		1 mm² (recommended)
flexible with ferrule with plastic sleeve	0.2 mm² ... 1 mm²
flexible with ferrule with plastic sleeve		1 mm² (recommended)
rigid (AWG)	24 ... 14 (Cu)
Stripping length	10 mm (rigid/flexible)
Stripping length		10 mm (Ferrule)

LED signaling
Types of signaling	LED
Signal threshold	> 0,9 x U_N(U_N = 24 V DC) (LED lights up green)
Signal threshold		< 0,9 x U_N(U_N = 24 V DC) (LED off)

Electrical properties
Number of phases	1.00
Insulation voltage input/output	4 kV AC (type test)
Insulation voltage input/output		3.75 kV AC (routine test)

Product properties
Product type	Power supply
MTBF (IEC 61709, SN 29500)	> 3440000 h (25 °C)
		> 2000000 h (40 °C)
		> 1370000 h (50 °C)
Environmental protection directive	RoHS Directive 2011/65/EU
		WEEE
		Reach
Insulation characteristics
Protection class	II (in closed control cabinet)
Degree of pollution	2

Dimensions
Width	54 mm
Height	90 mm
Depth	55 mm (Device depth (DIN rail mounting))
Depth	61 mm
Horizontal pitch	3 Div. (DIN 43880)
Installation dimensions
Installation distance right/left	0 mm / 0 mm
Installation distance top/bottom	30 mm / 30 mm

Mounting
Mounting type	DIN rail mounting
Assembly instructions	alignable: 0 mm horizontally, 30 mm vertically
Mounting position	horizontal DIN rail NS 35, EN 60715
With protective coating	No

Material specifications
Flammability rating according to UL 94	V0 (Housing, terminal blocks, base latches)
Housing material	Plastic
Foot latch material	Polyamid
Housing material	Polycarbonate

Environmental and real-life conditions
Ambient conditions
Degree of protection	IP20
Ambient temperature (operation)	-10 °C ... 70 °C (Derating: > 50 °C; 2 %/K)
Ambient temperature (storage/transport)	-40 °C ... 85 °C
Ambient temperature (start-up type tested)	-25 °C
Maximum altitude	≤ 4000 m (> 2000 m, Derating: 10 %/1000 m)
Max. permissible relative humidity (operation)	≤ 95 % (at 25 °C, non-condensing)
Shock (operation)	18 ms, 30g, per spatial direction (IEC 60068-2-27)
Vibration (operation)	< 15 Hz, amplitude ±2.5 mm (IEC 60068-2-6)
Vibration (operation)		15 Hz ... 150 Hz, 2.3g, 90 min.

Standards and regulations
Overvoltage category
EN 61010-1	II (≤ 4000 m)
Overvoltage category
EN 62477-1	III (≤ 2000 m)
Electrical safety
Standards/specifications	IEC 61010-1 (SELV)
Electrical safety
Standards/specifications	IEC 61010-1 (SELV)
		IEC 61010-2-201 (PELV)
Electrical safety
Standards/specifications	IEC 61558-2-16
Electrical safety
Standards/specifications	EN 61204-3
Electrical safety
Standards/specifications	IEC 61010-1
Electrical safety
Standards/specifications	DIN EN 60335-1

Approval data
UL
Identification	UL 1310 Class 2 Power Units
UL
Identification	UL/C-UL Listed UL 61010-1
UL
Identification	UL/C-UL Listed UL 61010-2-201
UL
Identification	UL/C-UL Listed ANSI/UL 121201 Class I, Division 2, Groups A, B, C, D (Hazardous Location)

EMC data
Low Voltage Directive	Conformance with Low Voltage Directive 2014/35/EC
Electromagnetic compatibility	Conformance with EMC Directive 2014/30/EU
Conducted noise emission	EN 55016
Conducted noise emission		EN 61000-6-3 (Class B)
Interference emission	Noise emission according to EN 61000-6-3 (residential and commercial) and EN 61000-6-4 (industrial)
Noise emission	EN 55016
Noise emission		EN 61000-6-3 (Class B)
Noise immunity	EN 61000-6-2:2005
Harmonic currents
Standards/regulations	EN 61000-3-2
Standards/regulations		EN 61000-3-2 (Class A)
Flicker
Standards/regulations	EN 61000-3-3
Frequency range	0 kHz ... 2 kHz
Electrostatic discharge
Standards/regulations	EN 61000-4-2
Electrostatic discharge
Contact discharge	6 kV (Test Level 3)
Discharge in air	8 kV (Test Level 3)
Comments	Criterion A
Electromagnetic HF field
Standards/regulations	EN 61000-4-3
Electromagnetic HF field
Frequency range	80 MHz ... 1 GHz
Test field strength	10 V/m (Test Level 3)
Frequency range	1 GHz ... 6 GHz
Test field strength	10 V/m (Test Level 3)
Comments	Criterion A
Fast transients (burst)
Standards/regulations	EN 61000-4-4
Fast transients (burst)
Input	asymmetrical 4 kV (Test Level 4)
Output	asymmetrical 2 kV (Test Level 3)
Comments	Criterion A
Surge voltage load (surge)
Standards/regulations	EN 61000-4-5
Input	symmetrical 2 kV (Test Level 4)
Input		asymmetrical 4 kV (Test Level 4)
Output	symmetrical 1 kV (Test Level 3)
Output		asymmetrical 2 kV (Test Level 3)
Comments	Criterion B
Conducted interference
Standards/regulations	EN 61000-4-6
Conducted interference
Input/Output	asymmetrical
Frequency range	0.15 MHz ... 80 MHz
Comments	Criterion A
Voltage	10 V (Test Level 3)
Voltage dips
Standards/regulations	EN 61000-4-11
Voltage	230 V AC
Frequency	50 Hz
Voltage dip	70 %
Number of periods	25 periods
Additional text	Class 3
Comments	Criterion A
Voltage dip	40 %
Number of periods	10 periods
Additional text	Class 3
Comments	Criterion A
Voltage dip	0 %
Number of periods	1 period
Additional text	Class 3
Comments	Criterion A
Criterion A	Normal operating behavior within the specified limits.
Criterion B	Temporary impairment to operational behavior that is corrected by the device itself.
Criterion C	Temporary adverse effects on the operating behavior, which the device corrects automatically or which can be restored by actuating the operating elements.