The store will not work correctly in the case when cookies are disabled.
Input data| AC operation |
| Network type | Star network |
| Nominal input voltage range | 100 V AC ... 240 V AC |
| Input voltage range | 100 V AC ... 240 V AC -15 % ... +10 % |
| Input voltage range AC | 85 V AC ... 264 V AC |
| Electric strength, max. | ≤ 300 V AC 15 s |
| Typical national grid voltage | 120 V AC |
| 230 V AC |
| Voltage type of supply voltage | AC/DC |
| Inrush current | ≤ 16 A (typical) |
| Inrush current integral (I2t) | < 0.6 A2s |
| Inrush current limitation | typ. 16 A (after 1 ms) |
| AC frequency range | 50 Hz ... 60 Hz ±10 % |
| Mains buffering time | typ. 20 ms (120 V AC) |
| typ. 100 ms (230 V AC) |
| Current consumption | 2.2 A (100 V AC) |
| 1.9 A (120 V AC) |
| 1.1 A (230 V AC) |
| 1.1 A (240 V AC) |
| Nominal power consumption | 272 VA |
| Protective circuit | Transient surge protection; Varistor |
| Power factor (cos phi) | 0.5 |
| Typical response time | < 1 s |
| Input fuse | 6.3 A (internal (device protection)) |
| Recommended breaker for input protection | 6 A ... 16 A (Characteristics B, C, D, K) |
| Discharge current to PE | < 0.25 mA |
| DC operation |
| Nominal input voltage range | 110 V DC ... 250 V DC |
| Input voltage range | 99 V DC ... 275 V DC |
| Switch-on voltage | ≥ 88 V DC |
| Shut-down voltage | < 60 V DC |
| Voltage type of supply voltage | AC/DC |
| Mains buffering time | > 100 ms (230 V AC) |
| Current consumption | 1.4 A (110 V DC) |
| 0.6 A (250 V DC) |
Output data| Efficiency | > 90 % (for 230 V AC and nominal values) |
| Output characteristic | U/I with dynamic load reserve |
| Nominal output voltage | 24 V DC ±1 % |
| Setting range of the output voltage (USet) | 24 V DC ... 28 V DC (> 24 V DC, constant capacity restricted) |
| Nominal output current (IN) | 5 A |
| Dynamic Boost (IDyn.Boost) | 7.5 A (5 s) |
| Derating | > 60 °C ... 70 °C (2.5%/K) |
| Feedback voltage resistance | ≤ 35 V DC |
| Protection against overvoltage at the output (OVP) | ≤ 30 V DC |
| Control deviation | < 1 % (change in load, static 10 % ... 90 %) |
| < 3 % (Dynamic load change 10 % ... 90 %, 10 Hz) |
| < 0.1 % (change in input voltage ±10 %) |
| Residual ripple | < 50 mVPP (with nominal values) |
| Output power | 120 W |
| 180 W |
| Maximum no-load power dissipation | < 1 W |
| Power loss nominal load max. | < 16 W |
| Rise time | ≤ 12 ms (UOUT (10 % ... 90 %)) |
| Connection in parallel | yes, for redundancy and increased capacity |
| Connection in series | yes |
| Signal: DC OK |
| Maximum switching voltage | 30 V AC/DC |
| Continuous load current | 100 mA |
Connection data| Input |
| Connection method | Push-in connection |
| Conductor cross section solid min. | 0.2 mm² |
| Conductor cross section solid max. | 4 mm² |
| Conductor cross section flexible min. | 0.2 mm² |
| Conductor cross section flexible max. | 2.5 mm² |
| Conductor cross section AWG min. | 24 |
| Conductor cross section AWG max. | 12 |
| Stripping length | 10 mm |
| Output |
| Connection method | Push-in connection |
| Conductor cross section solid min. | 0.2 mm² |
| Conductor cross section solid max. | 4 mm² |
| Conductor cross section flexible min. | 0.2 mm² |
| Conductor cross section flexible max. | 2.5 mm² |
| Conductor cross section AWG min. | 24 |
| Conductor cross section AWG max. | 12 |
| Stripping length | 8 mm |
| Signal |
| Connection method | Push-in connection |
| Conductor cross section solid min. | 0.2 mm² |
| Conductor cross section solid max. | 1.5 mm² |
| Conductor cross section flexible min. | 0.2 mm² |
| Conductor cross section flexible max. | 1.5 mm² |
| Conductor cross section AWG min. | 24 |
| Conductor cross section AWG max. | 16 |
| Stripping length | 8 mm |
LED signaling| Types of signaling | LED |
| Floating signal contact |
| Signal output: LED status indicator |
| Signalization designation | DC OK |
| Status display | “DC OK” LED |
| Color | green |
Electrical properties| Number of phases | 1.00 |
| Insulation voltage input/output | 3 kV AC (type test) |
| 1.5 kV AC (routine test) |
Product properties| Product type | Power supply |
| MTBF (IEC 61709, SN 29500) | > 3380000 h (25 °C) |
| > 1970000 h (40 °C) |
| > 900000 h (60 °C) |
| Insulation characteristics |
| Protection class | II (in closed control cabinet) |
| Degree of pollution | 2 |
Dimensions| Width | 35 mm |
| Height | 130 mm |
| Depth | 115 mm |
| Installation dimensions |
| Installation distance right/left | 0 mm / 0 mm |
| Installation distance top/bottom | 50 mm / 50 mm |
Mounting| Mounting type | DIN rail mounting |
| Assembly instructions | alignable: horizontally 0 mm (≤ 40 °C) 10 mm (≤ 70 °C), vertically 50 mm |
| Mounting position | horizontal DIN rail NS 35, EN 60715 |
| With protective coating | No |
Material specifications| Inflammability class in acc. with UL 94 (housing / terminal blocks) | V0 |
| Housing material | Plastic |
| Type of housing | Polycarbonate |
| Hood version | Polycarbonate |
Environmental and real-life conditions| Ambient conditions |
| Degree of protection | IP20 |
| Ambient temperature (operation) | -25 °C ... 70 °C (> 60 °C Derating: 2,5 %/K) |
| Ambient temperature (storage/transport) | -40 °C ... 85 °C |
| Ambient temperature (start-up type tested) | -40 °C |
| Maximum altitude | ≤ 5000 m (> 2000 m, Derating: 10 %/1000 m) |
| Climatic class | 3K3 (in acc. with EN 60721) |
| Max. permissible relative humidity (operation) | ≤ 95 % (at 25 °C, non-condensing) |
| Shock | 18 ms, 30g, in each space direction (according to IEC 60068-2-27) |
| Vibration (operation) | < 15 Hz, amplitude ±2.5 mm (according to IEC 60068-2-6) |
| 15 Hz ... 150 Hz, 4g, 90 min. |
Standards and regulations| Rail applications | EN 50121-4 |
| Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations | EN 50178/VDE 0160 (PELV) |
| Standard – Limitation of mains harmonic currents | EN 61000-3-2 |
| Standard - Electrical safety | IEC 62368-1 (SELV) |
| Standard – Safety extra-low voltage | IEC 62368-1 (SELV) und EN 60204-1 (PELV) |
| Standard - Safe isolation | DIN VDE 0100-410 |
| Standard - Safety of transformers | EN 61558-2-16 (air clearances and creepage distances only) |
Approval data| UL approvals | UL Listed UL 508 |
| UL/C-UL Recognized UL 60950-1 |
| Conformity/Approvals |
| SIL in accordance with IEC 61508 | 0 |
EMC data| Low Voltage Directive | Conformance with Low Voltage Directive 2014/35/EC |
| Electromagnetic compatibility | Conformance with EMC Directive 2014/30/EU |
| EMC requirements for noise emission | EN 61000-6-3 |
| EN 61000-6-4 |
| EMC requirements for noise immunity | EN 61000-6-1 |
| EN 61000-6-2 |
| Noise emission | EN 55011 (EN 55022) |
| Noise immunity | EN 61000-6-2:2005 |
| Electrostatic discharge |
| Standards/regulations | EN 61000-4-2 |
| Electrostatic discharge |
| Contact discharge | 6 kV (Test Level 4) |
| Discharge in air | 8 kV (Test Level 4) |
| Comments | Criterion A |
| Electromagnetic HF field |
| Standards/regulations | EN 61000-4-3 |
| Electromagnetic HF field |
| Frequency range | 80 MHz ... 1 GHz |
| Test field strength | 10 V/m (Test Level 3) |
| Frequency range | 1 GHz ... 2 GHz |
| Test field strength | 10 V/m (Test Level 3) |
| Frequency range | 2 GHz ... 3 GHz |
| Test field strength | 10 V/m (Test Level 3) |
| Comments | Criterion A |
| Fast transients (burst) |
| Standards/regulations | EN 61000-4-4 |
| Fast transients (burst) |
| Input | 4 kV (Test Level 4 - asymmetrical) |
| Output | 2 kV (Test Level 3 - asymmetrical) |
| Signal | 1 kV (Test Level 2 - asymmetrical) |
| Comments | Criterion A |
| Surge voltage load (surge) |
| Standards/regulations | EN 61000-4-5 |
| Input | 3 kV (Test Level 3 - symmetrical) |
| 6 kV (Test Level 4 - asymmetrical) |
| Output | 1 kV (Test Level 2 - symmetrical) |
| 2 kV (Test Level 3 - asymmetrical) |
| Signal | 1 kV (Test Level 2 - asymmetrical) |
| Comments | Criterion B |
| Conducted interference |
| Standards/regulations | EN 61000-4-6 |
| Conducted interference |
| Input/Output | asymmetrical |
| Frequency range | 0.15 MHz ... 80 MHz |
| Comments | Criterion A |
| Voltage | 10 V (Test Level 3) |
| Emitted interference |
| Standards/regulations | EN 61000-6-3 |
| Radio interference voltage in acc. with EN 55011 | EN 55011 (EN 55022) Class B, area of application: Industry and residential |
| Emitted radio interference in acc. with EN 55011 | EN 55011 (EN 55022) Class B, area of application: Industry and residential |
| Criterion A | Normal operating behavior within the specified limits. |
| Criterion B | Temporary impairment to operational behavior that is corrected by the device itself. |
In order for the Goods to be eligible for a return, please make sure that:
The Goods were purchased in the last 14 days
The Goods are in the original packaging
The Goods were not used or damaged
